Basic blacksmithing
Essential kit, coal, coke or gas, setting up safely, carbon monoxide and fumes, basic techniques, heat colours, first projects, steels, and neighbours.
By Michael Johnson · Updated 19 November 2026 · How we check our guides
Basic blacksmithing lets you make and repair hooks, brackets, hinges, pokers, tool handles and simple tools from scrap steel: genuinely useful skills when replacement parts are hard to get. A small forge can be set up in a garden or workshop for modest cost. This guide covers the essential kit, coal, coke and gas forges, setting up safely, carbon monoxide and fumes, basic techniques and heat colours, first projects, steels and hardening, neighbours, and learning.
1. Essential kit
- Forge: solid fuel or gas.
- Anvil: a proper anvil is best; a heavy block of steel on a stump works to start.
- Hammers: a cross-pein of around 1–1.5 kg to begin.
- Tongs: to fit the stock you're working.
- Vice: a leg (post) vice suits hot work.
- Quench tub of water, wire brush, files, a hacksaw or angle grinder.
- Safety kit: safety glasses, ear protection, a leather apron and natural-fibre clothing (synthetics melt).
2. Coal, coke or gas
| Forge | Pros | Cons |
|---|---|---|
| Coal | Traditional, flexible heat, good for welding | Smoky, sulphur in poor coal, fire management to learn |
| Coke | Less smoke than coal | Needs constant air blast |
| Propane (gas) | Clean, quick to start, easy to control | Gas cylinder safety, harder to heat just one spot |
| Charcoal | Can be home-made. See the charcoal guide | Burns fast, sparks |
Solid fuel forges need an air supply from a blower or bellows; a small 12 V blower can run from a battery. See the off-grid workshop guide.
3. Setting up safely
- Work on a non-flammable floor (concrete, stone, compacted earth), away from buildings, fences and anything that can catch fire.
- Keep a fire extinguisher and a bucket of water handy. See the fire extinguisher guide.
- Anvil face at about knuckle height when standing.
- Keep children and pets well away; hot metal looks cold long before it's safe to touch.
- Store gas cylinders upright outdoors. See the LPG safety guide.
4. Carbon monoxide and fumes
- All forges produce carbon monoxide; gas forges can produce a lot when running rich.
- Work outdoors, under an open-sided shelter, or with a proper hood and flue, plus a CO alarm. See the CO safety guide.
- Never heat galvanised or plated steel, or metal with paint or coatings.
- Stop and get fresh air if you get a headache, dizziness or nausea.
5. Basic techniques
- Drawing out: making metal longer and thinner, for points and tapers.
- Upsetting: making a section thicker by hammering on the end.
- Bending and scrolling over the anvil horn or in the vice.
- Twisting square bar for decorative and stronger pieces.
- Punching and drifting holes.
- Work only while the metal is hot enough; hammering steel that's too cold can crack it.
6. Heat colours
| Colour (seen in shade) | Roughly | Use |
|---|---|---|
| Dull red | Around 600–700 °C | Light bending |
| Cherry red | Around 750–850 °C | Hardening many carbon steels |
| Orange to yellow | Around 900–1,100 °C | Main forging range |
| Bright yellow-white, sparking | Above about 1,200 °C | Too hot: the steel is burning |
7. First projects
- S-hooks and wall hooks.
- A fire poker or campfire tools.
- Tent pegs and fence staples.
- Gate latches and simple hinges.
- Simple tongs, as you'll need more.
8. Steels, hardening and tempering
- Mild steel is easy to forge but doesn't harden much; good for hooks and brackets.
- Higher-carbon steels (old files, springs, chisels) can be hardened by quenching and then tempered to reduce brittleness, for tools and blades.
- Scrap steel of unknown type behaves unpredictably; test a small piece first.
- Made a knife? Keep UK knife carrying laws in mind. See the sharpening guide.
9. Neighbours and rules
- Hammering is loud and coal smoke can be a nuisance; councils can act on statutory nuisance from noise or smoke.
- In smoke control areas, burning coal that causes smoke may be restricted; gas forges avoid this.
- Check your home insurance covers a hobby forge.
10. Frequently asked questions
Is a gas or coal forge better for beginners?
A small propane forge is clean and easy to control; coal gives more flexible heat but takes more skill and is smokier.
Can I use a forge in my garage?
Only with very good ventilation, a non-flammable floor and a CO alarm. Outdoors or under an open-sided shelter is safer.
What steel should I start with?
Mild steel bar, about 10–12 mm square or round, for hooks and pokers.
11. Sources
- Make:, blacksmithing basics: makezine.com
- University of Arizona Cooperative Extension, forge and shop safety: arizona.edu
- Southern Ohio Forge and Anvil, coal forge vs gas forge: spaco.org
New to some of the terms? See the glossary. Not sure where to start? Try start here.