Home › Guides › Batteries in series and parallel

Connecting batteries in series and parallel

Series and parallel, wiring a parallel bank, wiring in series, fusing, mixing batteries, lithium banks, balancing series strings, and how many batteries.

By Michael Johnson · Updated 19 November 2026 · How we check our guides

Few off-grid systems use a single battery for long. You may want more capacity (batteries in parallel), a higher system voltage (batteries in series), or both. Done well, a battery bank behaves like one big battery; done badly, some batteries work harder than others, wear out early, or a fault in one damages the rest. This guide explains series and parallel connections, wiring a bank so the batteries share the load evenly, fusing, mixing old and new or different batteries, lithium banks with their own BMS, balancing series strings, and how many batteries to connect.

Golden rules: use identical batteries (same make, model, capacity and age), connect them with equal-length cables, take the main positive and negative from opposite ends of the bank (or use busbars), and fuse each battery or string.

1. Series and parallel

ConnectionVoltageCapacity (Ah)Example with 12 V 100 Ah batteries
Parallel (+ to +, − to −)Stays the sameAdds upTwo batteries: 12 V 200 Ah (2.56 kWh for LiFePO₄)
Series (+ to −)Adds upStays the sameTwo batteries: 24 V 100 Ah
Series-parallelBothBothFour batteries: 24 V 200 Ah

The stored energy (Wh) is the same either way. Higher voltage means lower current for the same power, so thinner cables and smaller losses. See the 12, 24 or 48 V guide and the battery bank size calculator.

Batteries wired in parallel and in seriesParallel: same voltage, more AhSeries: more voltage, same Ah12 V 100 Ah+−12 V 100 Ah+−12 V 100 Ah+−+ out− outResult: 12 V, 300 Ah+ from the first battery, − from the last12 V 100 Ah+−12 V 100 Ah+−link+ out− outResult: 24 V, 100 Ah− of one battery to + of the nextPositiveNegative
Left: three batteries in parallel, with the positive taken from the first battery and the negative from the last (diagonal wiring) so they share the load evenly. Right: two batteries in series to double the voltage. Fuse the bank as described below.

2. Wiring a parallel bank

3. Wiring in series

4. Fusing

5. Mixing batteries

MixAdvice
Old and new of the same modelAvoid; the old battery drags the new one down. If you must, only in parallel and only with small age differences
Different capacities, same chemistryAvoid in series; possible in parallel but they won't share load evenly
Lead-acid and lithiumDon't connect directly together; they need different charging voltages. Use a DC-DC charger between separate banks
Different lithium brandsAvoid; BMS behaviour and voltages differ

6. Lithium banks

7. Balancing series strings

8. How many batteries?

9. Frequently asked questions

How do I wire batteries in parallel properly?

Use identical batteries and equal-length cables, and either take the main positive and negative from opposite ends of the bank or connect each battery to busbars.

Can I mix an old and new battery?

It's best not to. The older battery limits the new one and can shorten its life.

Can I connect lithium and lead-acid batteries together?

Not directly. They need different charging voltages. Keep them as separate banks, linked by a DC-DC charger if needed.

10. Sources

  1. Victron Energy, Wiring Unlimited: battery bank wiring: victronenergy.fr
  2. Victron Energy community, diagonal battery wiring: victronenergy.com
  3. Victron Energy community, which battery cabling to prefer: victronenergy.com

New to some of the terms? See the glossary. Not sure where to start? Try start here.