Boat electrical wiring: 12 V DC systems and shore power
How to wire a yacht, motor boat or narrowboat safely: battery banks and switches, where fuses go and how big, marine cable and voltage drop, connections that last, routing and labelling, negatives and bonding, charging, ignition protection, shore power and electric shock drowning, corrosion, annual checks and the standards in the UK, USA and Australia.
By Michael Johnson · Updated 17 November 2026 · How we check our guides
Boat wiring lives in the harshest environment of any electrical system: salt, damp, vibration, fuel vapour and a hull that's always wet. Most boat electrical fires and failures come down to a handful of causes: unfused cables, corroded or loose connections, chafed insulation and mixed-up shore power earthing. This guide covers 12 V and 24 V DC systems and shore power on yachts, motor boats, narrowboats and small craft, with the standards in the UK, USA and Australia.
1. How a boat's electrics are laid out
Most boats have:
- A start battery for the engine and a house bank for everything else, so you can never flatten the engine battery by running the fridge.
- Battery switches to isolate each bank and, sometimes, to combine them in an emergency.
- A DC distribution panel with a breaker or fuse for each circuit.
- Charging from the engine's alternator, plus solar, wind or a shore-power charger.
- On larger boats, a shore power inlet feeding an AC panel, and sometimes an inverter.
2. Battery banks and switches
- Use deep-cycle batteries (AGM, gel, or LiFePO4) for the house bank and a cranking battery for the engine. See the lithium upgrade guide before going lithium.
- Size the house bank from your daily use: a sailing boat with autopilot, fridge and instruments often uses 100–250 Ah a day at 12 V. Use the battery bank size calculator.
- Battery switches must be rated for the starting current, easily reached and clearly labelled. The Boat Safety Scheme counts unlabelled or hidden isolators among its most common fails.
- Bilge pumps with float switches, and sometimes alarms, are normally wired before the main switch (with their own fuse) so they work when the boat's left switched off.
- Secure batteries so they can't move more than about 10 mm in any direction, even in a capsize; use boxes or trays that contain spills for flooded and AGM types.
- Ventilate flooded lead-acid battery compartments to outside; they give off hydrogen when charging.
3. Fusing: where and how big
Every positive conductor needs overcurrent protection as close as practical to the battery or other power source. ABYC E-11 sets the distances most marine electricians work to:
| Situation | Fuse or breaker within |
|---|---|
| Typical connection to a battery or bus | 7 in (178 mm) |
| Fed from a source other than a battery terminal (for example a bus or switch), sheathed along its whole length | 40 in (1 m) |
| Connected directly to a battery terminal and sheathed or enclosed along its whole length | 72 in (1.83 m) |
| Engine cranking circuit | Exempt from overcurrent protection (keep it short and well protected) |
- The fuse protects the cable: its rating must not exceed the cable's current rating.
- The main battery fuse must be able to break the battery's short-circuit current. ABYC E-11 (2025) gives default interrupt ratings where the maker doesn't state one: 3,000 A per 100 Ah for flooded lead-acid, and 5,000 A per 100 Ah for AGM, gel, TPPL and lithium. Class T or MRBF fuses are the usual choice for large banks.
- Use the fuse size calculator.
4. Marine cable and voltage drop
- Use tinned, fine-stranded copper cable (ABYC/UL 1426 "boat cable" or equivalent, or tri-rated tinned cable). Untinned copper wicks water and turns black and brittle inside the insulation.
- Never use solid-core household cable on a boat; vibration breaks it.
- Insulation should be rated at least 105 °C in engine spaces and resistant to oil and fuel.
- Voltage drop: ABYC uses 3% for critical circuits (navigation lights, bilge pumps, electronics, panel feeds) and 10% for non-critical ones (cabin lights). Run the numbers with the DC cable size calculator, remembering to count the round-trip length.
- Minimum sizes: ABYC sets 16 AWG (about 1.3 mm²) as a general minimum outside panels, with 18 AWG allowed in bundles of at least three.
5. Connections that last
- Crimp, don't twist: use tinned ring terminals with adhesive-lined heat-shrink, crimped with a ratchet crimper (or hydraulic for large cables). See crimping in the campervan wiring guide.
- Ring terminals, not fork (spade) terminals, on terminal studs, unless the fork has locking ends.
- No more than four terminals on one stud; use a bus bar for more.
- Solder alone isn't a mechanical connection: it creates a stiff point where strands break under vibration. ABYC doesn't allow solder as the sole means of connection.
- Butt connectors with adhesive heat-shrink are fine for joins; avoid wire nuts and household "chocolate block" connectors.
- Protect connections in wet areas with heat-shrink or a dielectric grease, not tape.
6. Routing, support and labelling
- Run cables as high as possible, above the bilge water line, and away from fuel lines and hot exhausts.
- Support cables at least every 18 in (450 mm) with non-metallic clips or ties that won't cut the insulation.
- Protect cables with grommets or conduit where they pass through bulkheads or bear against edges.
- Keep AC and DC cables apart, or in separate sheaths, and clearly identified.
- Label both ends of every cable. Keep a wiring diagram aboard.
- Use the colour codes for your standard: under ABYC, DC negatives are yellow (or black) and positives red; under ISO 10133, negatives are black or yellow.
7. Negatives, DC grounding and bonding
- All DC negatives return to a common negative bus, connected to the battery negative and to the engine block (DC grounding point). Use a battery monitor shunt on the main negative if fitted.
- Never use the hull, engine, or bonding conductors as a current-carrying return for a circuit (except the engine's own starter and alternator).
- A bonding system links underwater metal fittings (through-hulls, rudder stock, shaft) to the boat's anodes and DC grounding point, to help control corrosion and, under ABYC, provide a lightning and fault path. Whether to bond, and how, depends on the hull material and standard; get advice for your boat.
8. Charging: alternator, solar, wind, shore
- Alternator: charge the house bank through a voltage-sensitive relay or, better (and essential for lithium), a DC-DC charger or external regulator. Keep the start battery separate.
- Solar: semi-flexible panels on a bimini or hard panels on an arch; an MPPT controller close to the batteries with a fuse on the battery side. See the charge controller calculator.
- Wind: a marine wind generator needs a regulator with a dump load so it never runs unloaded; see the small wind turbine guide.
- Shore charger: a marine-rated multi-stage charger, set to your battery chemistry.
9. Ignition protection in petrol boats
In engine compartments and spaces with petrol (gasoline) engines or tanks, any electrical equipment must be ignition-protected: designed so it can't ignite fuel vapour (ISO 8846 or SAE J1171). That includes starters, alternators, bilge blowers, fuel pumps, switches and fuses. In the USA, this is a federal requirement for boat builders under 33 CFR 183 Subpart I. Diesel engine spaces don't need ignition-protected equipment, but keep it clear of fuel anyway.
Run the bilge blower for at least four minutes before starting a petrol inboard, and sniff the bilge.
10. Shore power and electric shock drowning
When a boat on shore power has a fault that leaks current into the water, people swimming nearby can be paralysed and drown. Proper shore-power installation protects against it:
- RCD / ELCI: a 30 mA RCD (UK, Australia) or an equipment leakage circuit interrupter (US, typically 30 mA under ABYC) on the boat's main AC supply trips on leakage.
- Main breaker and polarity: a double-pole main breaker at the inlet, and a reverse-polarity indicator, important in older marinas.
- Galvanic isolator or isolation transformer: fitted in the earth (green) conductor, it blocks small DC galvanic currents travelling between boats through the shore earth, while still passing fault current. An isolation transformer completely separates the boat's AC from the shore.
- Use a proper marine shore cable and connectors, never a household extension lead, and connect the boat end first.
- Have shore-power wiring installed and tested by a qualified marine electrician; it's licensed electrical work in Australia.
Size your shore supply with the hook-up and shore power calculator.
11. Galvanic and stray-current corrosion
- Galvanic corrosion: different metals in seawater form a battery; the less noble metal (aluminium, zinc) corrodes. Anodes are sacrificed to protect more important fittings; replace them when half gone.
- Stray-current corrosion: DC current leaking through the hull or fittings from a wiring fault can eat a through-hull or outdrive in weeks. Causes include a positive cable chafed against a fitting, a pump wired with a damaged negative, or a bilge full of water touching connections.
- Test for leakage by measuring current between the battery negative and the disconnected main negative with everything switched off: more than a few milliamps (other than known standby loads) means a fault.
12. Standards and rules by country
United Kingdom
- New boats sold in the UK are built to the Recreational Craft Regulations 2017, using ISO 10133 (extra-low voltage DC) and ISO 13297 (AC) as the usual standards.
- Boats on most inland waterways (Canal & River Trust, Environment Agency, Broads Authority) need a Boat Safety Scheme certificate every four years for private boats. Electrical checks include battery security, accessible and labelled isolators, protected and supported cables, and appropriate fusing.
- Shore-power installations in marinas follow BS 7671 Section 709; on the boat, follow ISO 13297 and have AC work done by a competent electrician.
United States
- ABYC E-11 (AC and DC electrical systems) and E-13 (lithium-ion batteries) are the industry standards used by builders, surveyors and insurers; both were revised in 2025.
- 33 CFR 183 Subpart I is the federal law for builders, covering ignition protection, battery installation, overcurrent protection and conductor requirements for boats with petrol engines.
- Marina shore power follows NEC Article 555, which requires ground-fault protection on shore power receptacles.
Australia
- AS/NZS 3004.2 covers electrical installations on boats; AS/NZS 3004.1 covers marinas. AS/NZS 3000 refers to them.
- Low-voltage (230 V AC) work on a boat is electrical work requiring a licensed electrician. Extra-low voltage DC (up to 120 V ripple-free) generally isn't, except in hazardous locations such as petrol engine spaces.
- Commercial vessels follow the National Standard for Commercial Vessels (NSCV Part C5B).
13. Annual checks
- Check battery terminals for corrosion and tightness; clean and re-grease.
- Look for chafed, cracked or hot-looking cables, especially at bulkheads and in the engine space.
- Test the RCD/ELCI with its test button.
- Check navigation lights, bilge pumps and float switches work.
- Measure stray current with everything off.
- Inspect and replace anodes.
- Check the shore cable and plugs for damage and burnt pins.
- Update your wiring diagram for any changes.
14. Frequently asked questions
What wire should I use on a boat?
Tinned, fine-stranded copper cable rated for marine use, at least 105 °C in engine spaces. Never solid-core household cable.
Where should fuses go on a boat?
As close to the battery as practical: ABYC E-11 calls for 7 in (178 mm) for most connections, extended to 40 in or 72 in only where the cable is sheathed or enclosed along its whole length. The engine cranking circuit is exempt.
Do I need a galvanic isolator?
If you use shore power, a galvanic isolator (or isolation transformer) protects your underwater metals from galvanic currents coming through the shore earth from other boats. It's strongly recommended for any boat that's often plugged in.
What is electric shock drowning?
When AC current leaks into the water from a faulty boat or dock, it can paralyse swimmers, who then drown. RCD/ELCI protection on the boat and the dock, and never swimming in marinas, prevents it.
Can I do my own boat wiring?
In the UK and USA you can generally work on your own boat's DC system, but it must meet the relevant standards and pass any Boat Safety Scheme or insurance survey. Shore-power AC work should be done by a qualified electrician, and in Australia it's licensed work.
What voltage drop is acceptable on a boat?
ABYC uses 3% for critical circuits such as navigation lights, bilge pumps and electronics, and 10% for non-critical circuits like cabin lighting.
15. Sources
- eCFR, 33 CFR Part 183 Subpart I, electrical systems: ecfr.gov
- US Coast Guard, electrical compliance guidelines for boat builders: uscgboating.org
- Panbo, ABYC updated battery and electrical standards (E-11 and E-13, 2025): panbo.com
- Boat Safety Scheme, core examination checking procedures (edition 5): boatsafetyscheme.org
- Boat Safety Scheme, 10 most common fails: boatsafetyscheme.org
- Standards Australia, AS/NZS 3004.2:2014 boat installations: standards.org.au
- Maritime Safety Queensland, electrical standards and licences for boats: msq.qld.gov.au
New to some of the terms? See the glossary. Not sure where to start? Try start here.