Off-grid LED lighting
Lumens, watts and colour, how much light you need, types of LED lighting, 12 V or 24 V, wiring a lighting circuit, voltage drop, switches and dimmers, backup lighting in a mains home, and outdoor lighting.
By Michael Johnson · Updated 18 November 2026 · How we check our guides
Lighting is usually the first thing people want in a power cut and the easiest thing to run from a battery. Modern LEDs produce several times more light per watt than old bulbs, so a whole cabin, van or emergency room can be lit for a few watts. This guide explains how to plan low-voltage LED lighting for an off-grid building, van, boat or backup circuit: choosing fittings and strips, 12 V or 24 V, brightness and colour, wiring and voltage drop, switches and dimmers, and keeping a few lights running from batteries when the mains fails.
1. Lumens, watts and colour
- Lumens measure light output. An old 60 W bulb gave about 800 lumens; an LED gives that from about 6–8 W.
- Efficacy (lumens per watt) varies: cheap LEDs and strips may give 60–80 lm/W, good ones 100–150 lm/W or more.
- Colour temperature: warm white (2,700–3,000 K) is cosy for living areas; neutral or cool white (4,000–5,000 K) suits kitchens, workshops and tasks.
- CRI (colour rendering index): 80+ is fine; 90+ shows colours more accurately for cooking, first aid and crafts.
- Red light preserves night vision and is useful for night checks.
2. How much light you need
| Space | Lumens (roughly) | LED watts |
|---|---|---|
| Small bedroom or bathroom | 200–400 | 2–4 W |
| Living room (ambient) | 800–1,500 | 7–15 W |
| Kitchen worktop | 500–1,000 over the work area | 5–10 W |
| Reading lamp | 300–500 | 3–5 W |
| Van or boat living area | 300–800 | 3–8 W |
| Workshop | 2,000+ | 20 W+ |
Task lighting where you need it is far more efficient than lighting a whole room brightly.
3. Types of LED lighting
- 12 V LED fittings: downlights, ceiling lights and reading lights made for caravans, boats and cabins. Look for wide input ranges (10–30 V) so they tolerate charging voltages.
- LED strips: flexible, cheap, easy to fit under cupboards or along ceilings. Use aluminium channels to help them dissipate heat and last longer.
- 12 V LED bulbs: G4, MR16 and similar, for existing low-voltage fittings.
- USB lights: run from power banks. See the USB-C guide.
- Battery lanterns and head torches for portable light. See the lighting and candles guide.
4. 12 V or 24 V?
- Match lights to your battery system voltage, or use a DC-DC converter.
- 24 V strips and fittings draw half the current of 12 V ones for the same power, so voltage drop is lower and longer runs are possible.
- Cheap 12 V strips designed for a regulated 12 V supply may run hot or fail early on a battery that reaches 14.4–14.6 V when charging. Choose fittings rated for battery systems, or feed them through a regulator.
- See the 12 V, 24 V or 48 V guide.
5. Wiring a low-voltage lighting circuit
- Run lighting from its own fused circuit on the DC distribution board. Lighting currents are small, so 3–10 A fuses are typical.
- Use suitable cable sized for current and length; twin, tinned marine cable resists corrosion in damp places.
- Join cables with proper connectors, not twisted wires and tape.
- Mark low-voltage DC circuits so nobody confuses them with mains.
- Follow 12 V wiring basics and use the fuse size calculator.
6. Voltage drop and long runs
At 12 V, even a small voltage drop dims LEDs or causes uneven brightness along a strip. Long strips (over about 5 m) should be fed at both ends or from the middle, and long cable runs need thicker cable. Use the DC voltage drop calculator and the DC cable size calculator. Aim for under 3% drop.
7. Switches, dimmers and sensors
- Use switches rated for DC: some mains switches are fine at low voltage, but check.
- PWM LED dimmers save energy and let you set just enough light.
- Motion sensors for porches, hallways and sheds avoid lights left on.
- Touch switches on many 12 V fittings are handy in vans and boats.
- Smart controllers can switch circuits from your phone, but add standby drain.
8. Backup lighting in a mains-powered home
- Rechargeable "emergency" LED bulbs fit normal light fittings and keep glowing for a few hours when the power fails (the light switch must be left on).
- Plug-in emergency lights that come on automatically in a power cut are ideal for hallways and stairs.
- A small 12 V LED circuit from a battery or power station can light key rooms for days.
- Battery lanterns are the simplest option. See the power cut plan and the lighting calculator.
- Avoid candles where you can: they're a major fire risk.
9. Outdoor and security lighting
- Solar-powered security lights with motion sensors work in power cuts.
- Choose IP65 or better for outdoor fittings.
- Light paths, steps and gates for safety. See the home security guide.
- Avoid bright lights that shine into neighbours' windows or the night sky.
10. Frequently asked questions
How many watts of LED lighting do I need for a room?
Typically 5–15 W for a living room and 2–4 W for a small bedroom, with good-quality LEDs.
Are 12 V or 24 V LED strips better?
24 V strips suffer less voltage drop and suit longer runs. Use 12 V if your battery system is 12 V, or a converter.
Why do my LED strips dim at the far end?
Voltage drop. Feed long strips from both ends or the middle, and use thicker cable.
11. Sources
- Simple Lighting, 12 V vs 24 V LED strip lights: simplelighting.co.uk
- HitLights, voltage drop in long LED strip runs: hitlights.com
- Victron Energy, Wiring Unlimited: victronenergy.com
New to some of the terms? See the glossary. Not sure where to start? Try start here.