Thermal stores
What a thermal store is, how much heat it holds, linking heat sources, hot water from a store, sizing, installation, safety and hygiene, and alternatives.
By Michael Johnson · Updated 19 November 2026 · How we check our guides
A thermal store is a large, well-insulated tank of water that stores heat rather than hot water for washing. Heat can go in from several sources (a wood stove with a back boiler, solar thermal panels, a heat pump, surplus solar electricity) and come out to radiators and, through a heat exchanger, to taps. For off-grid and wood-heated homes it's the hub that ties everything together. This guide explains how thermal stores work, how much heat they hold, linking sources, hot water by heat exchanger, sizing, safety, and the alternatives.
1. What a thermal store is
- A large insulated cylinder (often 200–1,000 litres or more) full of heating water, called primary water.
- Heat sources warm the water; heating circuits draw heat out.
- Hot water for taps passes through a coil or plate heat exchanger, so the stored water is never drunk.
- Many are open-vented (low pressure) yet deliver mains-pressure hot water through the heat exchanger.
2. How much heat it holds
Heat (kWh) = litres × temperature rise (°C) × 4.19 ÷ 3,600 (about 1.16 Wh per litre per °C)
| Store size | Heated from 40 °C to 80 °C (40 °C rise) |
|---|---|
| 300 litres | About 14 kWh |
| 500 litres | About 23 kWh |
| 1,000 litres | About 47 kWh |
Use the thermal store capacity calculator. The usable range depends on the lowest temperature your radiators or taps can still use.
3. Linking heat sources
- Wood stove with back boiler or log boiler: the store soaks up a hot burn and releases heat for hours, letting the fire burn hot and clean. See the wood burner guide.
- Solar thermal panels: via a coil low in the store. See the solar thermal guide.
- Immersion heaters: for surplus solar PV or off-peak electricity. See the diverter guide.
- Heat pumps and gas or oil boilers: can work with stores, but need careful design to keep efficiency.
4. Hot water from a thermal store
- Cold mains water passes through a coil or a plate heat exchanger and comes out hot at mains pressure.
- A thermostatic mixing valve is essential: water straight from a hot store can scald.
- The hot water flow rate depends on the store temperature and the heat exchanger size.
- See the off-grid hot water guide.
5. Sizing
- For a wood boiler, stores are often sized so that one full burn is absorbed without overheating; makers give litres per kW guidance.
- For solar thermal, about 50–100 litres per square metre of collector is common.
- Bigger stores lose more heat; insulation quality matters as much as size.
- Check floor loading: 1,000 litres of water weighs a tonne, plus the tank.
6. Installation and insulation
- Put the store inside the heated envelope so lost heat isn't wasted.
- Insulate pipes, especially the first metre or two from the store.
- Stratification matters: hot water rises; connect flows and returns at the right heights.
- Building regulations apply to heating and hot water systems; use a competent installer.
7. Safety and hygiene
- Solid fuel circuits need a heat leak or safety radiator, an open vent or approved safety devices, and pumps on a supply that keeps running (a power cut can stop a pump while the fire is still hot).
- Fit a thermostatic mixing valve on hot water outlets to prevent scalds.
- Because hot water is heated instantly through a heat exchanger rather than stored, the risk of Legionella in stored drinking water is reduced; still follow good practice for any stored hot water (store at 60 °C, deliver at 50 °C or above, with mixing valves at outlets).
8. Alternatives
- A twin-coil unvented or vented cylinder for solar plus boiler hot water.
- Phase-change heat batteries: smaller, but more expensive per kWh.
- Storage heaters for off-peak electric heating. See the storage heaters guide.
9. Frequently asked questions
How much heat does a 500 litre thermal store hold?
About 23 kWh between 40 °C and 80 °C (500 × 40 × 1.16 Wh).
Is a thermal store the same as a hot water cylinder?
No. A thermal store holds heating water; tap water is heated as it passes through a heat exchanger. A cylinder stores the hot water you use.
Does a thermal store work in a power cut?
The stored heat remains, and gravity-fed hot water may still flow, but pumped heating circuits stop. Solid fuel circuits need a gravity heat leak for safety.
10. Sources
- Energy Saving Trust, thermal energy stores: energysavingtrust.org.uk
- DIYFAQ Wiki, thermal stores and heat banks: diyfaq.org.uk
- HSE, Legionella in hot and cold water systems: hse.gov.uk
- Heatweb, what is a thermal store: heatweb.co.uk
New to some of the terms? See the glossary. Not sure where to start? Try start here.