Home › Guides › Fault finding

Fault finding off-grid and van electrics

A step-by-step method for finding faults with a multimeter, from the battery outwards: battery not charging, solar not producing, inverter cutting out, a battery going flat overnight, no power at all, hot connections and lithium BMS problems.

By Michael Johnson · Updated 17 November 2026 · How we check our guides

When an off-grid or van electrical system stops working, the cause is usually simple: a blown fuse, a loose connection, a wrong setting, a battery protecting itself. This guide gives a calm, step-by-step method to find the fault with a multimeter, covering "battery not charging", "inverter keeps cutting out", "solar not working", "battery dies overnight" and more, with quick checks you can do before calling anyone.

Work safely. Battery systems can deliver enormous currents: remove rings and watches, use insulated tools, and never short battery terminals. Don't open inverters or work on mains (AC) wiring unless you're qualified. If anything is hot, smoking or smells of burning, isolate it and get help.

1. The method: from the battery outwards

  1. Look and smell: burnt smell, melted insulation, a tripped breaker, an error code on a display.
  2. Check the battery: its voltage at the terminals, and for lithium, the BMS status in the app.
  3. Check the main fuse and isolator.
  4. Work outwards along the path to the failed part, measuring voltage at each connection, until it disappears.
  5. Check settings: charger profiles, low-voltage cut-offs, app settings.
  6. Change one thing at a time and note what you've done.

2. Using a multimeter

12 V battery at restLead-acid (AGM/flooded)LiFePO4
Full12.7–12.9 V13.4–13.6 V
About half12.2–12.3 V13.1–13.2 V
Nearly empty11.8–11.9 V12.0–12.8 V

Measure after the battery has rested for an hour with no charge or load. See the battery voltage chart; lithium's flat curve makes voltage a poor guide in the middle (see the battery monitoring guide).

3. Battery not charging

CheckWhat you'll seeFix
Charger output voltage at the battery terminals while chargingShould be 13.8–14.6 V (12 V system)If lower at the battery than at the charger: voltage drop in cables or connections
Fuse between charger and batteryBlown, or a breaker trippedReplace; find out why it blew
Charger settingsWrong battery type or voltageSet the correct profile
DC-DC charger triggerNo ignition/D+ signal, or smart alternator not detectedCheck the trigger wire and settings
Lithium BMSCharging blocked (too cold, too high voltage, cell imbalance)Check the app; warm the battery; balance
Battery itselfVoltage rises fast and falls fast; old or sulphated lead-acidLoad test or capacity test; replace

4. Solar not producing

  1. Check the sun: early morning, late afternoon, cloud and shade (even a small shadow on one cell) cut output hugely.
  2. Read the controller: PV voltage, PV current and battery voltage.
  3. PV voltage zero: check the panel isolator, MC4 connectors, string fuses and roof gland. Measure open-circuit voltage at the panel.
  4. PV voltage normal but no current: battery already full (normal), controller fault or wrong settings, or battery disconnected.
  5. PV voltage low: one panel in a series string is shaded or faulty, or a connector is damaged.
  6. Controller error: overvoltage in cold weather (too many panels in series), or over-temperature.
  7. Compare against expected yield with the solar panel output calculator; see the charge controller guide.

5. Inverter cuts out or won't start

SymptomLikely causeCheck / fix
Low-voltage alarm when a big load startsVoltage drop in thin or long cables, loose lugs, weak batteryMeasure voltage at the inverter terminals under load; thicker, shorter cables; tighten lugs
Overload when a motor startsStart-up surge too bigSoft-starter or a bigger/low-frequency inverter
Inverter and lithium battery both go deadBMS over-current tripCheck BMS current rating; add a battery in parallel
Over-temperaturePoor ventilation or a blocked fanClear space around it; clean the fan
RCD trips on the inverterEarth leakage in an appliance or cable, or neutral–earth problemsUnplug appliances one at a time; see the earthing guide
Spark and click, then nothing, when connectingCapacitor inrush tripping the BMS or fuseUse a pre-charge resistor or switch

6. Battery flat overnight or draining

  1. Turn everything off, then measure the standby current with a clamp meter on the main negative, or read it from the battery monitor.
  2. Normal standby loads: battery monitor, alarm, gas detector, router: typically 0.05–0.5 A. An inverter left on can draw 1–3 A at 12 V.
  3. Pull fuses one at a time until the drain disappears to find the circuit.
  4. Common culprits: inverter idle draw, a 3-way fridge left on 12 V, a stuck relay, a USB socket's LED, a diesel heater controller, a faulty cable chafing to chassis.
  5. Work out what your loads should use with the power consumption calculator.

7. No power at all

8. Finding voltage drop and hot connections

9. Lithium battery problems

10. Frequently asked questions

Why is my leisure battery not charging?

Most often a blown fuse, a wrong charger setting, voltage drop from thin cables or a poor connection, a DC-DC charger not getting its ignition signal, or a lithium battery blocking charge because it's too cold.

Why does my battery go flat overnight?

A standby drain: an inverter left on, a fridge on 12 V, or a fault. Measure the current with everything off and pull fuses one at a time to find it.

Why does my inverter keep cutting out?

Usually voltage drop on the DC side during big loads, a battery or BMS that can't supply the current, or a motor's start-up surge.

Why is my solar panel not producing power?

Shade, a faulty connector or fuse, a battery that's already full, or a controller error. Check PV voltage and current at the controller.

11. Sources

  1. Victron Energy, which solar charge controller: PWM or MPPT: victronenergy.com
  2. Victron Energy, careful – alternator charging lithium: victronenergy.com

New to some of the terms? See the glossary. Not sure where to start? Try start here.