Powering a radio station off-grid
How much radios draw, an energy budget, choosing a battery, charging from solar and the car, wiring and voltage drop, avoiding interference, and a portable kit.
By Michael Johnson · Updated 19 November 2026 · How we check our guides
A radio station that only works when the mains is on isn't much use in an emergency. Most mobile and base radios run on about 13.8 V DC, which makes them natural partners for 12 V batteries and solar panels. This guide covers how much current radios draw, sizing a battery for a day of operating, LiFePO4 and lead-acid, charging from solar and the car, voltage drop and connectors, fusing, keeping power supplies and chargers from causing radio interference, and a simple portable kit.
1. How much radios draw
| Radio | Receive | Transmit (full power) |
|---|---|---|
| 100 W HF transceiver | About 1–2 A | About 20–23 A |
| 10–20 W portable HF transceiver | About 0.3–1 A | About 3–5 A |
| 50 W VHF/UHF mobile | About 0.5–1 A | About 10–13 A |
| CB mobile (4 W) | About 0.3–0.5 A | About 1–2 A |
| Handheld (5 W) | Internal battery | About 1.5 A from its battery |
Check your radio's manual. Reducing power on transmit saves a lot: 50 W instead of 100 W roughly halves transmit current.
2. An energy budget
- Speech isn't continuous: on SSB, average transmit current is a fraction of peak. Data modes like FT8 transmit at full set power for the whole transmit period.
- Example: a 100 W HF radio listening for 2 hours at 1.5 A uses 3 Ah. Transmitting for 30 minutes of SSB at an average of about a quarter of 20 A, plus receive current between overs, uses roughly another 3 Ah. About 6 Ah in total.
- Use the radio battery run time calculator and the 12 V power consumption calculator.
3. Choosing a battery
- LiFePO4: holds about 13.2–13.3 V for most of its discharge, close to what radios want, and is light. Ideal for 100 W HF.
- Lead-acid (AGM): heavy and its voltage falls under load; radios may reduce power or cut out at low voltage.
- For 100 W HF, a battery that can supply 25 A or more without large voltage sag is needed; check the BMS limit on lithium.
- See the battery types guide and the battery bank size calculator.
4. Charging from solar and the car
- A 50–100 W solar panel with an MPPT controller keeps a 20–50 Ah battery topped up for typical operating.
- In a vehicle, a DC-DC charger charges a station battery from the alternator. See the DC-DC charging guide.
- Switch-mode chargers and MPPT controllers can be noisy on HF; see below.
- See the solar battery charge time calculator.
5. Wiring, connectors and voltage drop
- At 20+ A, a few metres of thin cable can lose a volt or more; keep leads short and thick. See the DC cable sizing guide.
- Anderson Powerpole connectors are widely used in amateur and emergency radio for quick, polarised connections.
- Fuse both positive and (if supplied) negative leads as the radio maker specifies; a fuse in the negative lead protects against a lost vehicle earth.
- A DC distribution box with fused outlets keeps a station tidy. See the busbars guide.
6. Avoiding radio interference
- Cheap switch-mode power supplies, chargers, LED lights and DC-DC converters can create noise across HF.
- Running the radio directly from a battery, with noisy chargers switched off during operating, gives the quietest reception.
- Use ferrite chokes on DC leads and choose well-filtered equipment.
- See the radio interference from solar guide and the DC-DC converters guide.
7. A portable station
- Radio, LiFePO4 battery (around 20–50 Ah), fused Powerpole leads and a small distribution box.
- Folding solar panel and small MPPT controller.
- Wire antenna, throw line and coax. See the emergency antennas guide.
- Logbook, frequency list, headphones, head torch.
- See the emergency radio guide.
8. Frequently asked questions
What battery do I need for a 100 W HF radio?
A LiFePO4 battery of around 20–50 Ah that can deliver at least 25 A covers most operating sessions; reduce power to stretch it.
Can I run a radio straight from a 12 V battery?
Yes. Most radios are designed for 13.8 V and work well from 12–14 V; LiFePO4 is especially well suited.
Why is my HF noisy on solar?
Charge controllers and switch-mode chargers can generate interference. Run from the battery with chargers off, and add ferrites.
9. Sources
- RSGB, EMC and solar PV panels: rsgb.org
- RSGB, becoming a radio amateur FAQ: rsgb.org
- Victron Energy, Wiring Unlimited: victronenergy.com
New to some of the terms? See the glossary. Not sure where to start? Try start here.