Home › Guides › Solar panels in series or parallel

Solar panels in series or parallel

Series, parallel and series-parallel, pros and cons, PWM and MPPT controllers, cold weather and maximum voltage, minimum voltage, shading, mixing panels, fusing, cable sizing and example layouts.

By Michael Johnson · Updated 18 November 2026 · How we check our guides

As soon as you have more than one solar panel, you have to decide how to connect them: in series (positive to negative, adding the voltages), in parallel (positives together and negatives together, adding the currents), or a mix of both. The choice affects how much power you get in shade and winter, how thick the cables need to be, which charge controller you can use, and whether the controller is safe on a frosty morning. This guide explains series, parallel and series-parallel wiring, shading, mismatched panels, the cold-weather voltage rise that can damage controllers, fusing, cable sizing, and practical layouts for vans, sheds and homes.

Check the cold-weather voltage. A panel's open-circuit voltage (Voc) rises as it gets colder. On a bright, frosty morning, a series string can exceed the controller's maximum input voltage and damage it. Always check with the MPPT string voltage calculator using the coldest temperature you expect.

1. Series, parallel and series-parallel

ConnectionVoltageCurrentExample: two 200 W panels (Vmp 20 V, Imp 10 A)
SeriesAdds upSame as one panel40 V, 10 A
ParallelSame as one panelAdds up20 V, 20 A
Series-parallel (2 strings of 2)Two panels' worthTwo panels' worthFour panels: 40 V, 20 A

Power is the same in theory either way; what changes is voltage, current, and how the array behaves in real conditions. Work out any combination with the solar panel series and parallel calculator.

2. Pros and cons

SeriesParallel
Cable sizeThinner cable (lower current)Thicker cable needed
Long cable runsBetter: lower lossesWorse
Low light and winterReaches the controller's start voltage soonerMay struggle to start in dull light with low-voltage panels
Partial shadingShade on one panel affects the string (bypass diodes help)Each panel works more independently
ControllerNeeds an MPPT controller with a high enough voltage ratingWorks with PWM or lower-voltage MPPT
FusingUsually no string fuses for a single stringFuses often needed with three or more strings in parallel

3. PWM vs MPPT controllers

4. Cold weather and maximum voltage

5. Minimum voltage and hot weather

6. Shading

7. Mixing different panels

8. Fusing and isolators

9. Cable sizing

10. Example layouts

SystemTypical layout
Campervan, two 175 W panels, 12 V batterySeries if the controller allows (e.g. 100 V MPPT) for better low-light charging; parallel if roof vents shade one panel at a time
Shed, one 400 W household panel, 12 V batterySingle panel to a 100 V MPPT; check cold Voc
Off-grid home, 12 panels, 48 V batteryStrings of 3–4 panels in series on a 150 V or 250 V MPPT, with several strings in parallel or several MPPTs
East and west roof facesSeparate strings on separate MPPT inputs

11. Frequently asked questions

Is it better to wire solar panels in series or parallel?

Series gives higher voltage, thinner cables and better low-light performance with an MPPT controller. Parallel copes better with uneven shading and works with PWM controllers.

Why does solar panel voltage go up in the cold?

Panel voltage rises as temperature falls, typically about 0.3% per degree below 25 °C. Always check cold-weather Voc against the controller's maximum.

Can I mix different solar panels?

In series, panels need similar current; in parallel, similar voltage. Very different panels are best on separate charge controllers.

12. Sources

  1. Victron Energy community, effect of Voc on MPPT: victronenergy.com
  2. Victron Energy, SmartSolar MPPT 100/30 and 100/50 manual: operation: victronenergy.com
  3. SurgePV, solar panel stringing and wiring guide: surgepv.com

New to some of the terms? See the glossary. Not sure where to start? Try start here.